3/1/1988 Pontiac announces the end of the Fiero automobile – Was anyone sad about that?
Pontiac Fiero
3/1/1937 In New Jersey one of the largest dealerships of the era was opened. The Miro Brothers opened a state-of-the-art facility with “one of the largest and most modern showrooms in the country,” measuring 38′ x 40′ . The dealership was service station and dealt for Buick, Packard, Oldsmoble, and REO trucks. The east side of the building served as a Mobil gas station and service garage during the World War II.
As I get ready to start the new round of mods for my 1970 Mustang Coupe, I’m reminded of a couple of issues that came up when I was assisting a fellow Mustang owner doing a trans – transplant.
The first tip is partially dependent on what stage you are in of your restoration.
He has already finished most of the interior when the a transmission he wanted to add became affordable, it was a good deal…saving some $$$$.
He had decided to do the swap and add a short shifter. This of course requires the removal the bezel and the current 3 speed shift lever, which is easily done from inside the car.
Bezel and Boot
In the course of removing those two parts, he found that the opening cut in the new carpet was not going to allow the access necessary. An attempt to ‘widen’ it was successful but left a bit of a jagged slit. Additionally, while removing one of the screws it snagged the carpet and pulled a few loops out. Can you guess what the tip is? Yeah…remove the carpet and if possible make the swap before you put new carpet in.
One other quick tip is to apply a little silicone spray to the shifter to help slide the boot off..oh…yeah…removing the shift knob before the boot is a good idea…..DON”T ASK!!!!!
So I left a couple of photos out of the last post. But I wanted to show (IMHO) a couple stars of the show and one of the strange one.
I covered the Galaxies and 500’s, however, here are a couple more: (Come..on..you would be able to pick just one or two either!!!)
(In no particular order)
Crown Victorian (before the exploding gas tanks and cop lights)
Oh..the Chrome!!
Did I mention the Chrome?
Just look at that smile..I mean bumper!!!
Not really comparable to the Crown Vic – this Starliner was, although not original, very nicely done.
Ford Starliner with a little custom work.
Oh..check out the intake setup on that Starliner!!!!
OK.. I know at least one of my readers will like this next car.
It is a 1965 Ford Mustang Station Wagon. Originally a concept created by William Sibo (designer for Ford Motor Company). He actually built this car from the original drawings. Car is currently owned by Ken Berger. The car now has a 429, rack and pinion steering C-6 auto trans, coil over suspension and power brakes, A/C and stereo system.
No Middle Road - Hate it or Love it.
There you go!
I can’t get past the that rear end….but this helps:
Here some interesting facts for the new in 2008 LS9 engine.
– It was a combination of upgraded LS3 and LS7 components and took 3 years to develop
– All 2000 units were hand-assembled in GM’s Performance Build Center in Wixom, Michigan
-It displaced 6.2 liters
– Bore and stroke 4.06×3.62 with a compression ratio of 9.1:1
– It had reinforced bulkhead to improve block stiffness and used six bolt steel main caps.
– Of note the headgasketts were cut to the shape of the LS3 but had four layers of steel.
– Remember the “tornado”? That device that was sold and was added to your air intake and was supposed to funnel air into your carb or throttle body, booting HP? Well the LS9’s intake had “swirl ring” to improve the air flow.
– Sported the Eaton R1900 2 rotor supercharger, pumping out 2.3 liters of compressed air, but that’s all – this air was then super cooled by the Behr intercooler, that knocked off about 140 degrees.
– The valve were titanium on the intake side and stainless steel on the exhaust side
– The pistons were forged aluminum and the rods were titanium.
Here’s some output numbers:
At 1000 rpm – 300 hp and 320 lb-ft torque
The maximum was approx. 620 hp coming at 6500 rpm and 595 lb-ft of torque coming at 4000 rpm with nearly all of its top end torque available between 2600 and 6000 rpm.
Two days into 2010 and everything seems to be going fine, so far. :^)
I promised some details on my 1984 Corvette, so here ya go.
1984 was the first year for the new, much-awaited body style. There were no 1983 Corvettes, depending on what you read, there were a few made but not in production and were sold. Each generation of the Corvette has been placed in to generation categories. These were designated as C1 (1953-1962), C2 (1963-1967), C3 (1968-1982), C4 (1984-1996), C5 (1997-2003), and C6 (2004 to ……).
The C4 took a long time to develop, starting in 1978 (we’ll do more details another time), and was very innovative. For example, it had the Z51 racing suspension (a fairly new development), all digital dash with graphs as indicators for mph and rpms, extremely low drag co-efficient, and all electronic shifting transmission. We’ll cover more later on.
My C4 is red and came equipped with 205 hp 350 Crossfire Engine (more on this engine later on), Z51 suspension, electric driver’s seat, traga top. Here is a picture:
The story of how I obtained the Vette is a good one. So go get a beverage and sit back and read. This is one of those stories that I’ve always read about and said “What luck that guy had…nothing like that would happen to me.”
THE STORY
Actually, it’s a pretty cool story on how I came to own the Vette.
Purchased my 1970 Mustang a while ago (picture attached) and I wanted a fox body Mustang to go with it.
I had a cherry 1995 Toyota Celica with Bella Niche rims and I put it up on Craigs List offering to trade it for a fox body.
I got a call from a lady living here in Tucson that wanted the Celica for her daughter. I told her I wasn’t interested in selling it and she said didn’t want to purchase it but to trade a 1984 Vette for it. (I thought “No one trades a Corvette for a Toyota.”)
In the course of 3 months, it was an on again off again deal. She wanted to give her daughter a car for Christmas, but her daughter wanted the Vette. But props to Mom, she wasn’t going to give a 16 year old that kind of car. In our conversations it was revealed that the daughter tossed a fit and said she didn’t want the Celica. Christmas came and went and in January the lady calls me again.
Finally, we set a time to meet, but still I was thinking either the Vette was trashed or something was up. I was also concerned that the perception might be that I took advantage of her, to me who in their right minds would trade an American icon car for an import? To my surprise we agreed to meet at her husband’s Auto A/C shop. So I started feeling a little bit better, at least her husband must know something about cars. So I showed up and things improved, the husband actually had a restored Ford Galaxy and another in the works. They got better when he stated that the Vette was his wife’s car and she wouldn’t drive it and it’s just taking up space. She bought it but never really drove it.
I was even more pleased when I found the Vette in excellent shape (recent repaint that wasn’t great but not too bad, I grew up in an auto body shop, so I know good paint). It was all original, only 32k miles with the Crossfire engine (I didn’t know much about the Crossfire..but I sure do now as I’ve recently rebuild the injector towers). Anyway, both cars went up on the lift and we looked them over and test drove each others. Vette had very good power, shifted a little hard, but not too bad. We agreed to sleep on it and within a week I was the 3rd owner of the C4. Title swap only.
Yeah, I know, this was one of those deals you only read about in a car magazine.
