Welcome back to #ProjectSportsRoof. I’m finishing the re-positioned shifting rod above the transmission’s cross member.
Next I’ll need to go top side and give the selector a try. If that is working properly, hitting the proper gears I can spin the torque converter and properly torque its connection to the flex plate.
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in my 1973 Mustang. The next step is to check the compression. First up was to warm the car a bit and then pull the plugs. Here’s what the …
This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …
It’s past time to get it in gear and get the transmission back in shape to get the power from the newly bored out .040 351 Cleveland to the rear wheels.
With the help of my nephew Josh (thanks Josh!!) the transmission was effortlessly (ha) in to place…almost.
Here a more current status video.
All Bolted in.
Now that it’s all bolted in place, I need to work on the getting the kick down road back in place. That’s coming up next on #ProjectSportsRoof.
Welcome back to #ProjectSportsRoof. I run my car projects much like I run my IT projects. You always have to know where to start and know the end game. As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
Well it’s been a long week getting her back on the road. But she drove well enough given her condition.
I am looking for opinions on kits for front suspension rebuilds, mine is shot. At this point I’m probably looking for the cheapest most comprehensive kit given my pony’s condition.
My entire front suspension is not suspending, or bouncing, or quiet. Its time for a full rebuild but I’ve been waiting to blow my motor to justify a full car build! It’s been on its last leg for at least 10 years so at this point I’m trying to see how far I can go to prove Ford’s reliability before tearing her down and she just won’t die! A true survivor.
Also I have a mean top end tick I have lots of play in my lifters, I’m assuming that’s the problem. Already replaced the valve caps, but I probably lost one or two again, any tips or tricks to adjust these ticks?
Although she really like cruising at 50 mph everywhere! I had a hard time keeping it under that speed.
Josh,
You will get a lot of opinions and have a lot of options. Basically is comes down to what you want the car to be. If you just want a cruiser I think you can’t go wrong with just building like it came from the factory. I did that with my 1970 only difference is I use polyurethane bushing. Polyurethane bushing improved the ride without ruining the feel of how the car would have handled when it came from the factory. Properly greased the don’t squeak. If you want it a bit better ride you can upgrade components as you go.
I recommend the RPS kit (it is under $300)
Front Suspension Kit, 1968 – 73 Mustang Restoration Parts Source FDSUSKIT3 – RPS – 004 This suspension kit includes new upper and lower control arms with bushings and riveted ball joints installed, new spring perches and insulators and new strut rod bushings with washers.
Replaces that is, boot as in shifting boot. (Were you thinking…since I just got back from the Barrett Jackson Auction.. I was considering getting rid of the Stang ? Nope..but I tell you there were a couple of cars I’d even swap for…that’s for sure!!) When the 4 speed trans got …
If you searched and found or followed my posts on restoring the dash-board of my ’70 Mustang, then you might recall my planning/scheduling issues. As I was taking the old dash pad off, I realized that I hadn’t order the plastic pillar molding. When I finally called a few Mustang parts …
I’ve the pillar post moldings painted and ready to installed. I put on 3 coats of paint. Now I have to remove the dash pad (again) and install. That will be later this week, my Corvette is still in shop and the Mustang is my back up car. Thanks for reading more to …
Ok now I’m excited. The dash pad replacement arrived and it looks great. Here are some pics: I ordered this part from Dallas Mustang, but I thinking I should have ordered directly from DashesDirect.com I’ll check the web site and see if it was cheaper there. When you have an average guy’s budget …
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
I thought I’d take a minute and catch the readers up on #ProjectSportsRoof. I wanted to touch up some of the engine bay components, horns, vacuum canister and battery tray. I didn’t want to alter some of these too much, I like having the numbers, logos and other info visible, not …
I thought I’d take a minute and catch the readers up on #ProjectSportsRoof.
I wanted to touch up some of the engine bay components, horns, vacuum canister and battery tray. I didn’t want to alter some of these too much, I like having the numbers, logos and other info visible, not covered under a several layers of primer and paint. So these items were lightly sanded and then sprayed with primer and black engine paint.
Battery Tray – in the process of being sanded with dremel.
The horns were cleaned up with break cleaner then sanded by hand.
A lot of the paint just came off with the cleaning.
Horn in the process of being sanded.. Note the “LO” and other numbers. My goal is to keep them visible.
A coat of Eastwood Rust Encapsulator and then a primer coated applied – tried to keep the numbers, etc. visible.
A little more sanding and then some paint.
Vacuum Canister
Battery Tray and Horns
I think they came out O.K.
There is a quick video.
Coming up distributor install and transmission update.
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in my 1973 Mustang. The next step is to check the compression. First up was to warm the car a bit and then pull the plugs. Here’s what the …
This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …
Luxstang Wrote: I’m starting to get fed up with the car. The more I do on it the more seems to fail. Replaced the upper and lower control arms a few weeks ago. Took it for an alignment yesterday and the guy tells me he can’t adjust camber on the passenger side.. Turns out the hole in the rear ex-center washer is round so it no longer adjusts the camber properly. (Ok, when I replaced the control arms I could have sworn that washer was ok otherwise I wouldn’t have put it back in….) Now I gotta wait for 2-3 days for a new set of screws with washers to arrive. I had the wheels powder coated (and posted a thread about it) and I don’t like them anymore. The 18 inch rims rub with the new tires, I gotta get new ones but I don’t really want to either. The rear windows are out of the car as I’m waiting for WCCC to fix my pancake motors, so no interior in the back at all. Plus yesterday a big chip of paint flew off the rear quarter extension. I’ll need to try my painting skills on that…. I wonder if I shouldn’t just leave everything and simply drive the car into the ground as a daily driver and call it a day.
Hang in there with the Mustang, Luxstang, it will be even sweeter when you get it done!!!
My 73 is my second Mustang restoration (70 was my first) and my third personal restoration in the last few years. I can attest that you do run in to those periods of time when it seems that the car just doesn’t want to be restored.
Heck I bought and drove the 73, maybe 5-6 times and it bent a rod and burned a valve. Had the heads redone. Drove it 3 or 4 more times and then discovered a bottom end knock had to tear down the entire engine and send it out for machining and rebuild. While trying to get it back together I ran into wiring problem and drive train problems. Don’t even get me started on the rusted floor pans (now complete).
I restored my ’84 Corvette and I will tell you, there were day when I felt just like Luxstang (by the way he’s in Luxembourg). The Vette was powered by the infamous Cross-Fire engine. So many problems with the fuel system and multiple injector rebuilds, it was enough to drive you crazy.
Many folks do give up, you can find thousands projects on the internet looking for a new home.
But before you quit, go to the forums for you car, like Luxstang did, you’ll get some encouragement and maybe even helpful suggestions for getting through those periods. Con some friends or neighbors to give a hand. I found that a good motivator is to have neighbors come and see your progress. I have one neighbor that loves to look at what I’ve done and another (Dan T.) who has even spend more than a few hours giving me a hand with some of the tasks.
Restoring a car is not much different then most things you tackle in life. If you hang in there and stick it out to the end, it will be rewarding.
Did you think I sold #ProjectSportsRoof? Nope. I’ve been busy and I’ve been serving as editor to another cool project – my constant reader Bill’s ’68 Plymouth RoadRunner (#ProjectBeepBeep).
However, I have been doing some work on the sports roof and in this video you’ll see a little bling under the hood (not sure I like now that it’s done…but it’s easy to swap out). There is also a few venting and vacuum issue I need to deal with and you’ll see those in the video.
Here’s a look at the Vapor Canister vs the Vacuum Canister.
Vapor Canister
Vacuum Canister
As I mentioned in the video, the vapor canister was missing from the engine bay and the fuel vapor line was running into the vacuum canister and then vented to the stock air cleaning. After some research and help from the guys over on 7173 Mustangs forum I realized the problem and it’s an easy fix…although the vapor canister is pricey – without the charcoal!!! (: ^ 0 ).
Thanks for checking on #ProjectSportsRoof. So here is the last set of initial questions. Here is an image of the current set up: Any diagram I find has the hose vacuum from the Distr going to the Valve assy. The Valve assy has nothing attached which is located on the front …
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
Thanks for checking on #ProjectSportsRoof. So here is the last set of initial questions. Here is an image of the current set up: Any diagram I find has the hose vacuum from the Distr going to the Valve assy. The Valve assy has nothing attached which is located on the front …
It’s always cool to catch a car show when you are traveling.
This past week (Super Bowl Sunday) while visiting family in Alpharetta, Ga, (just outside of Atlanta) I got the chance to ride into the ‘big’ city and take in the event – Thanks Brian!!
There often more than 1500 cars on the first Sunday of every month and even though it was cold and damp (and it being Super Bowl Sunday and the home town team was playing) there were a lot of cars!!!
We got there as it was starting to break up but there were still a lot of cars. Here’s a few pics.
Take a look at this awesome creation. Built on a C4 Corvette body to best look like a 1957 Chevy!
Check out this Nissan!!! It’s power plant is in the next pic.
Nice straight six!!!!
Nice custom ride!!
Here is a great look for a Road Runner.
No one standing around new anything about the car.
I wasn’t even able to scratch the surface. There were rows of Mustangs and Corvettes, long with 100’s of European and Japanese high-end rides and not all of them ‘stock’.
Here are a couple more videos. Quality is not great in spots but it was the live feed through Facebook.
These videos take place at the entrance. I imagine that Ford pays good money to have their offering right up front. In these you’ll see the new Mustang and the Focus RS….both nice looking cars.
In this video you’ll also see the Eco-Boost Ford GT race car and the GT 350!!
There are more videos coming up including a discussion with one of the sellers as his car heads to the stage, a good look at a rear all aluminum Cobra and a clarification on what the stage works kept throwing to the side when the cars came up on stage.
2 days ago … This my version of the 2017 Barrett Jackson out here in Scottsdale Arizona. Its a mind blowing experience if you’ve never been before! There’s …
It is always cool attend a car auction but Barrett-Jackson events are top-notch!!!
For this trip I attempted to use Facebook Live as a platform and I can report that it worked, however video format showed up ‘sideways’ for many of the post, my android failed to compensate for wide-angle shots. I pulled down most of the videos and edited them to make it a bit easier to view.
Here is the first video in that series:
Hot Wheels!!!
Awesome looking van. One lady said “It just needs the plastic package!”
Jan 7, 2017 … NOT MINE , found online at ClassicCar.com. Super cool, a chance to own an original Transformer movie car purchased from the GM Heritage …
