I thought I’d take a minute finish up the write-up on the very first upholstery job. I finished it up a two weeks ago and really missed driving the Mustang, but that’s what happens when you do your own work and you can only fit it between all the normal life stuff that needs to get done.
Yes, as I was reminded twice by a couple of car acquaintances, I used a kit, some say they aren’t much different from slip covers, but as you can see in my shots here that’s a bit of an understatement.
Now these next two videos are not all that great but I think you can see the removal of the back and the fasteners. I’ve worked with these type of fasteners before in my father’s body shop (back in the early ’70s) nearly all door panels and seat back were fastened in that way. They work really well but bend them (and they do bend easy of they aren’t aligned with the hole and pressure is applied) and you’ll have to spend sometime reshaping them, even then they might not hold properly, or replace them.
Check out the videos:
Here are a few more photos and the finished product. Not to bad for my first one. I have the passenger’s side to do.
With the plastic seatback removed.
Needed to remove the back release
2 piece
release removed.
Helpful hint: All the hardware and fasteners have to pass through upholstery. Rather than try to cut holes, I made X cuts and pressed the screw or hardware through. This made it as tight as possible.
Markings on the Foam
Good shot of the cloth sleeve with the wire passed through.
Here you would pass the hog wire while in the hog-nose pliers through the cloth between the upholstery and the wire. You then have to shove this down between the two pieces of foam and grab a spring.
Finished product.
Replacing the seat track was done before I married the bottom and back. Placing it back in the car was a little tricky..until I figured out that moving the set on the track was the way to get the studs to drop back in to holes in the floor board.
Over all this was not as tough as I thought it would be. The passenger side will be quicker. I’ll post the final product on that side.
3. Reader choice – you choose the next engine to highlight
I have a couple commercial ventures on the near horizon:
1. Certified Auto Appraiser – I’m about to finish my certification and will be specializing in Classic, Muscle, Antique and speciality cars.
2. Auto restoration project management. Focus is on those individuals that love their cars, but don’t have the time nor the experience to know what needs to be done. I’m actually waiting for my first car. It is a 1975 VW Bug coming all the way from Iowa City, Iowa, should be here this will for inspection and the beginning of its restoration.
So what engine would you want to see highlighted? Drop me a note here or on Facebook.
I was recently talking to a coworker of mine who own a 1949 Pontiac Silver Streak Delivery Van (link – http://wp.me/pKHNM-Bx ) and we were discussing his 6 volt system and the troubles with low amperage.
Well I just ran across a couple of interesting articles dealing with that subject. Now I will tell you I am not “the guy” for electrical work – nope not me (I had a bad experience – ok – a couple of bad ones). But even this one I can understand.
Increasing the power supply often means that you need to convert to 12 volt and maybe 15 years ago yes, but now 6 volts are readily available. So here is what you do (sorry no pics)
Take two 6 volt batters and link them in parallel by connecting the two negative terminals to each other and the two positive to each other. The main positive cable goes from the positive terminal of the first battery to ground and the main negative cable is connected to the negative terminal of the second battery. Of course in some case you may have to modify the batter shelf, but it will sure help kick up the cold cranking amps.
Folks seem to like this segment so let’s continue with 1950.
19 major car makers existed back then and Chevy topped the production totals with 1,498,590 units followed closely by Ford with 1, 208,912. The rest of the field were all less than have that.
So you’ve read my review and I promised to drop a note as to the “Long Lasting” part of Griot’s Garage’s – Long Lasting Tire Dressing.
Now is has rained nearly every day since I applied the dressing.
So take a look at the tires with 2 applications and 3 applications.
Tires with 2 applications of tire dressing
Here is the tire with 3 applications of tire dressing
Here is what I think as a wrap up. Long lasting to me doesn’t necessarily mean just duration, but can it stand up to everyday driving – oh—yeah…just in case I failed to mention, the Vette is my daily driver. It lived up to the Griot promise. I’ll continue using this product.
