Update on Transmission for Project SportsRoof – ’73 Stang

Spend a few hours on this 2017 Labor Day, laboring over #ProjectSportsRoof and I wish that labor paid a bit more dividends.

The goal was to mate the transmission back to the engine but unfortunately that just wasn’t going to happen today.  The engine is set back a bit too far and tilted (on purpose).  Problem is if I bolted them up the engine hoist would be able to lift the engine and trans due to the height I needed the car to work on the transmission.

So I pulled the transmission out from under car and placed its wheels back on the concrete.

 

It was a major effort to get the car up high enough to get the transmission out.  I pushed the boundaries of safety with a floor jack and a couple of jack-stand.

As I stated in the video I may just take it down the street and have them get that straightened out for me.

More to come on #ProjectSportsRoof.

Thanks for reading.

Tim

 

1973 Mustang Project SportsRoof – Exterior Walk-Around

Welcome back to #ProjectSportsRoof.  I run my car projects much like I run my IT projects.  You always have to know where to start and know the end game.   As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …
1973 Mustang – Engine Bay Work

If you look back at #ProjectSportsRoof post you’ll see the condition engine bay.  During those videos I mentioned that I was going to clean it up and hit it with a rattle can.  Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
1973 Mustang – Project SportsRoof – Compression Test Part II

This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …

Project SportRoof – Transmission Update

It’s been a while but the new career is smoothing out and I’m hell-bent on getting back to my Mustang project.

Here is where we are with the drive train…going backward is necessary sometimes to get moving forward again.

 


 

HEY FOUND THEM:

 

 

More Coming Up on #ProjectSportsRoof.

Thanks for reading.

Tim

 

 

projectsportsroof

73 Mustang (Project SportsRoof) Engine Dress Up and Venting …

Mar 15, 2017 Did you think I sold #ProjectSportsRoof? Nope. I’ve been busy and I’ve been serving as editor to another cool project – my constant reader Bill’s …
Average Guy’s Car Restoration, Mods and Racing – Rebuild Them …

#ProjectSportsRoof has been…languishing a bit but I have a new transmission jack and I’ll be back to it in the next week…right now it going to be about 120 …

I like Stats – World-Wide Stats

I like stats!!!

0-60 mph, 0-100 mph stats, bore and stroke, torque stats and the world-wide stats for this site.

I like to take time to thank the viewer from around the world from time to time.

With over 40 different countries tuning in to check of progress on #ProjectSportsRoof and #ProjectBeepBeep I think it’s
cool to see such wide-spread interest.

So here’s some stats.

80% of the viewer are from the US.
3% are from Canada
2% from the UK
1% from Mexico, France, and Australia, Russia, German
Other countries, Saudis Arabia, Spain, Italy, Poland Netherlands, S. Korea
South Africa, India, Philippines, Thailand, Indonesia, New Zealand, Japan.

And here’s a big thanks:

THANKS!!!

1968 Ply Road Runner
Project BeepBeep

Project BeepBeep – 68 RoadRunner – Disc Brake Conversion Part 7 Bench Bleeding and More

Welcome back to #ProjectBeepBeep!

Bill is trying to finish up this the disc brake conversion and as things happen when you are dealing with our mechanical best friends, when you think its ready to go, things go south.

Look for the discussion on Dot 3 and Dot 5 brake fluid and tips for creating your own brake bleeding system.  And keep an eye out for DIY master cylinder bench bleeding tubes.

All excellent to note!!  Oh…and dig out that jack!!!

 


 

Lots more coming up on Project BeepBeep, so check back often.

Thanks for reading.

Tim

projectbeepbeep

Project BeepBeep – ’68 Road Runner – Drum or Disc – The Decision

1968 Ply Road RunnerProject BeepBeep Welcome back to #ProjectBeepBeep.  Bill is looking at the brakes and gets some professional assistance to help him make a crucial decision.  You know if you’ve got a lot of GO…you need a lot STOP. It not an easy decision to alter a car’s originality, especially …
Project BeepBeep – ’68 Road Runner -Disc Break Conversion Part 2

Thanks for checking back in on #ProjectBeepBeep. Having made the decision to convert the front brakes from shoe to disc Bill gets started with this major project for #ProjectBeepBeep. He went with a kit from Dr. Diff and here’s a brief look at some of the contents.   Nice shiny new rotors!! Spindle …
Project BeepBeep – 68 RoadRunner – Disc Brake Conversion Part 5 and Some Dash Work

Welcome back to #ProjectBeepBeep. Bill is working on finishing up the brake conversion. Here is a progress update. Note:  I forgot to add the credits for these videos:   Starring Bill B as himself; BeepBeep as ’68 Road Runner; Wild E. Coyote in effigy Camera Production; Mrs. Bill B and SamB Editing Tim …

Where The Heck Have You Been?

That’s a question I’ve gotten on other social media avenues and there is a good answer.

At this age I made a decision to make a career change.  Up at age of 58 and after 20 plus years as information technology guy (last position as Director of IT) I resigned and began the quest to make a move that I’ve always wanted to make.  So, it was back to college for a few courses and heavy-duty studying to pass certification exams – passed on the second attempt.

That’s where I’ve been.  Now I begin my new career as a High School teacher and that kicks off with my first teaching position at a charter school.  Things get rolling mid-July.

Now that will be a busy time but I’m comfortable with having spare time to keep working on my projects.

So, here’s what is coming up:

Bill has finished #ProjectBeepBeep disc brake conversion and we even have a video with it in motion!!!!

#ProjectSportsRoof has been…languishing a bit but I have a new transmission jack and I’ll be back to it in the next week…right now it going to be about 120 degrees, so not idea weather for working on the beast.

More #AutoFactoids coming up and some new stuff I have planned.

Thanks for checking back with us!!!

Tim

 

68 Ply RoadRunner (ProjectBeepBeep) Dash Update – YouTube

May 11, 2017 Bill sent out the circuit board that supplies the power to the all dash components on #ProjectBeepBeep.

Average Guy’s Car Restorations, Mods, and Racing

Bill is getting soooooooooo close to having ProjectBeepBeep on the road again. This update takes a look at the brake actuator rod. The Rod. Bill mentioned 303 …

Project SportsRoof – 73 Mustang – Getting in Gear with the Transmission Part 2

 

Welcome back to #ProjectSportsRoof.  I’m finishing the re-positioned shifting rod above the transmission’s cross member.

 

 

 

Next I’ll need to go top side and give the selector a try.  If that is working properly, hitting the proper gears I can spin the torque converter and properly torque its connection to the flex plate.

More coming up.

Tim

projectsportsroof

1973 Mustang – Engine Bay Work

If you look back at #ProjectSportsRoof post you’ll see the condition engine bay.  During those videos I mentioned that I was going to clean it up and hit it with a rattle can.  Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
1973 Mustang – Project SportsRoof – Compression Test Part I

I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in my 1973 Mustang. The next step is to check the compression. First up was to warm the car a bit and then pull the plugs. Here’s what the …
1973 Mustang – Project SportsRoof – Compression Test Part II

This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …

 

Project SportsRoof – 73 Mustang – Getting in Gear with the Transmission

It’s past time to get it in gear and get the transmission back in shape to get the power from the newly bored out .040 351 Cleveland to the rear wheels.

With the help of my nephew Josh (thanks Josh!!) the transmission was effortlessly (ha) in to place…almost.

 

 

 

Here a more current status video.

 

 

All Bolted in.

 

Now that it’s all bolted in place, I need to work on the getting the kick down road back in place. That’s coming up next on #ProjectSportsRoof.

Thanks for reading.

Tim

projectsportsroof

#ProjectSportsRoof – 1973 Mustang

1973 Mustang Project SportsRoof – Exterior Walk-Around

Welcome back to #ProjectSportsRoof.  I run my car projects much like I run my IT projects.  You always have to know where to start and know the end game.   As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …
1973 Mustang – Engine Bay Work

If you look back at #ProjectSportsRoof post you’ll see the condition engine bay.  During those videos I mentioned that I was going to clean it up and hit it with a rattle can.  Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …

Mini Car Show – TMC

It always cool to stumble upon a car show regardless of size.

TMC (Tucson Medical Center) opened up a new office just down the road.  My wife is a commercial interior designer and does a lot of work through her company for at the TMC facilities.

We were aware of the Grand Opening for this new building but we weren’t there’d be a car show.  Here a few of the cars that showed.

You just could walk past this 1959 GMC 100 Pickup.  So nicely restored.

 

Love the steel painted rims!!!

Lots of Chrome on that front end!!

Still being powered by the straight six! The golf club hood prop is a custom touch!

Sparse interior but 100% effective.

Here is a great looking 1962 Ford pickup  – still sporting its original V8.

Are you kidding me?  Look at this beautiful 66 Malibu!!!

 

327 Engine (245hp) with Factory Air!!!

Back end jacked up just right!!

There is a lot of tire on that back axle!

That’s all original interior folks!!!

 

Here are a few more Chevy’s

Beautiful Super Sport w/vinyl top

Wow…is that a BLOWER on top of that power plant?

And another BLOWER!!

56 Chevy Sporting a huge radiator

1980 El Camino – In great shape.

Beautiful Impala…OH…YES..that a Corvette LS3 engine!!!

If you are going to have only one Mopar show up, you want it to be the GTX!!  Take a look:

 

Plymouth Belvedere GTX.

Yes that is a 426 Hemi….going to find two carbs under that air cleaner.

Clean and original interior.

Here a few more of the cars that showed up.

Thanks to my wonderful wife who didn’t mind an interruption in our errands to spend a few minutes at this show.

Coming up more on #ProjectSportsRoof and #ProjectBeepBeep and keep an eye out for our first Facebook Live event.

Thanks for reading.

Tim

www.agcarrestoration.com

Project SportsRoof – 73 Mustang Distributor Install

Welcome back to #ProjectSportsRoof.  I’m moving ever closer to getting her back on the road.  Popped the distributor in recently.  Take a quick look.

 

Of course the 351C will need to be timed but I think I have this close enough so it will at least start when I’m ready to fire it up.

I have a bit more transmission work to do, I’ll show you the status in the next post.

Thanks for reading.

Tim

projectsportsroof

1973 Mustang – Engine Bay Work

If you look back at #ProjectSportsRoof post you’ll see the condition engine bay.  During those videos I mentioned that I was going to clean it up and hit it with a rattle can.  Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …

1973 Mustang – Project SportsRoof – Engine Bay Components.

I thought I’d take a minute and catch the readers up on #ProjectSportsRoof. I wanted to touch up some of the engine bay components, horns, vacuum canister and battery tray.  I didn’t want to alter some of these too much, I like having the numbers, logos and other info visible, not …

1973 Mustang – Project SportsRoof – Engine Bay Components.

I thought I’d take a minute and catch the readers up on #ProjectSportsRoof.

I wanted to touch up some of the engine bay components, horns, vacuum canister and battery tray.  I didn’t want to alter some of these too much, I like having the numbers, logos and other info visible, not covered under a several layers of primer and paint.  So these items were lightly sanded and then sprayed with primer and black engine paint.

 

Battery Tray – in the process of being sanded with dremel.

The horns were cleaned up with break cleaner then sanded by hand.

A lot of the paint just came off with the cleaning.

Horn in the process of being sanded.. Note the “LO” and other numbers. My goal is to keep them visible.

A coat of  Eastwood Rust Encapsulator  and then a primer coated applied – tried to keep the numbers, etc. visible.

A little more sanding and then some paint.

Vacuum Canister

Battery Tray and Horns

I think they came out O.K.

There is a quick video.

 


Coming up distributor install and transmission update.

Thank for reading.

Tim

1973 Mustang – Engine Bay Work

If you look back at #ProjectSportsRoof post you’ll see the condition engine bay.  During those videos I mentioned that I was going to clean it up and hit it with a rattle can.  Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
1973 Mustang – Project SportsRoof – Compression Test Part I

I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in my 1973 Mustang. The next step is to check the compression. First up was to warm the car a bit and then pull the plugs. Here’s what the …
1973 Mustang – Project SportsRoof – Compression Test Part II

This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …